MeiTrack VT310 Manuel d'utilisateur

Meiligao GPRS Communication Protocol Between GPS Tracker and Server Version 2.00 GT30i GT60 VT300 VT310 VT400 Change Version Reason of Ch

- 10 - Response: $$<L><ID><0x4115><Flag><checksum>\r\n Note: Flag =0x00, failure response; =0x01, success response.

- 11 - Above command will enable alarms when Input1 is active, Input2 is inactive, Input3 is either active or inactive, Input4 is active and Input5

- 12 - 16. Log by Interval – 0x4131 Command: @@<L><ID><0x4131><data><checksum>\r\n Description: Set time interval for

- 13 - Response: $$<L><ID><0x4135><Flag><checksum> \r\n Example: 24 24 00 12 40 10 47 20 21 3F FF 41 35 01 F8 51 0D 0A

- 14 - =1, TCP =2, UDP Example: 40 40 00 2E 40 10 47 20 21 3F FF 41 55 31 2C 31 31 33 2E 39 32 2E 31 31 31 2E 32 32 31 2C 38 30 35 32 2C 63 6D 6E 65

- 15 - =0,cancle =[1,4294967295] meter(s) Distance interval is suggested to be set above 300 meters. Example: 40 40 00 14 40 20 50 20 81 4F FF 43 03

- 16 - Response: $$<L><ID><0x5199><Flag><checksum> \r\n Note: Flag =0x00, failure response; =0x01, success response.

- 17 - Description: To get the authorized phone number. Note: Button no should be 0x01, 0x02 or 0x03. If button no is 0xff, it will read all authori

- 18 - =0x02 Call B button is pressed / Input 2 active =0x03 Call C button is pressed / Input 3 active =0x04 Input 4 active =0x05 Input 5 active =0x

- 19 - Annex 1: Description of data

- 2 - I. Command Format

- 20 - (3) HDOP, in ASCII code, 0.5-99.9. HDOP is blank when the tracking unit has no GPS fix. (4) Altitude, in decimal string. (5) State: Status

- 21 - For VT400 Bit0: Status of Out1 If Bit0=0: Out1 is closed; Bit0=1:Out1 is open. Bit1: Status of Out2 If Bit1=0: Out2 is closed; Bit1=1:Out2 i

- 3 - II. Command List

- 4 - III. Command Details

- 5 - Note: Flag =0x00, failure response; =0x01, success response. Once the interval is successfully set, the tracker will send the following positi

- 6 - ……. =0x0A, speed limit is set to 100km/h; ……. =0x14, speed limit is set to 200km/h. Max speed limit is 200km/h. Example: 40 40 00 12 12 34 56

- 7 - ABCDEFGHIJ (defaulted as 0x01 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x01): A=0x00, turn off the function of replying with an SMS position re

- 8 - 10. Sleep Mode – 0x4113 Command: @@<L><ID><0x4113><power-saving level (1 byte in hex code)><checksum>\r\n Descr

- 9 - C=0x01, open output (OUT3) -connect to GND; C=0x02, remain previous status. D=0x00, close output (OUT4) -open drain; D=0x01, open output (OUT4